When before the time of writing is not smooth or started, pressing with the thumb hole about what black rubber pressed in the end, increase the pressure of the ink pen, the pressure increasingly large, the more the fuel. Instructions: writing on smooth, hard board ( such as surface, the floor ? ) Perpendicular to hold a pen. Performance: fast dry, high temperature, acid and alkali, water washing, anti- dyeing, not fade.įeatures : large capacity and extra thick aluminum pen, super-hard precision rolling Ball pen Tsui, black rubber wave control the ink flow, writing is extremely smooth, then ran out of ink does not dry. Record the appropriate measurement alongside the original measurement.Uses: Can be used for all kinds of fabric dyeing and finishing processes ( such as: cotton, hemp, silk, polyester, polyester, nylon, polyester and other fibers blended fabrics ) even after a series of cases of scouring, bleaching, dyeing, washing and other harsh after processing operations and do not fade, do not change, is not covered, it also clearly visible permanent marker. After conditioning the sample measure the distance between each pair of reference marks.ģ. After the appropriate cleansing and drying procedure lay the specimen flat and without stretching, preferably in a conditioned atmosphere for a minimum of 4 hours (wool products 16 hours).Ģ. Re-measurement and Appearance Assessment:ġ. This preparation is to assist ironing which is a general requirement of woven crinkle fabrics. Over lock the two pieces of fabric together down both length sides and over lock open both ends of tube of fabric, to prevent fraying. For woven crinkle fabrics two 500 mm square specimens with reference marks 350 mm apart, measure the distance between the marks as in 2.1.3. Over lock all four sides of the specimen to prevent fraying,Ħ. Record each measurement in order L1, L2, 元, W1, W2, and W3.ĥ. Lay the specimen flat and without stretching measure the distance between each pair of reference marks to the nearest mm.Ĥ. Mark the warp (length) direction in the top left hand corner. Do not cut specimens closer than 50 mm to a selvedge or cut edge. Mark three pairs of reference marks in the length direction and three pairs in the width direction of the specimen such that each pair is approximately 350 mm apart (See the Diagram Below).

A template can be employed to assist this preparation, on these occasions align one vertical edge parallel to the length threads (ends).Ģ. Cut a fabric specimen 500*500 mm with the edges parallel to the length and width of the fabric.

Non Phosphate Detergent A, Sodium Perborate and TAED in a 77:20:3 ratio.ġ. Advantageous for its ultra-high capacity, the Dalo Textile Marker provides a bright, sharp, rapid-drying permanent mark on synthetic and synthetic/cotton blended fabrics.

Ballast (Polyester make weights 200*200 mm). Advantageous for its ultra-high capacity, the Dalo T Stock Textile Marker provides a bright, sharp, rapid-drying permanent mark on synthetic and synthetic/.Calibrated steel rules of appropriate lengths graduated in cm and mm.Specifically designed for writing at all. Resists all modern textile processes Scouring, Dyeing, Laundry/Dry Cleaning, Bleaching, Finishing, Boil Off and Wood Fulling. Marker pens (texpen, dalo or laundry pen) These High Quality, Dalo ‘T’ Stock Paint Markers provide a rapid-drying, bright and sharp mark on synthetic and synthetic/cotton blended fabrics.Purpose: To determine the changes in dimension and appearance of fabrics and garments to specific cleansing or washing procedures. The marking remain permanent, bright & opaque. It is used by textile mills & processing houses before dyeing and finishing processes of grey fabric for identification, quality control, shrinkage, pilferage etc. Method: BS EN ISO 3759:1995, BS EN ISO 6330:2001 Century’s Tex Marker is a collapsible aluminum writing device filled with ink used for marking on fabric samples for identification. Fig: Dimensional Stability of Dyed Fabric

Resists all modern textile processes including scouring, dyeing, laundry/dry cleaning, bleaching, finishing, boil off, and wool fulling Perfect for use in textile labs for marking swatches Ergonomically correct marker enables you to mark at all angles. In this experiment I will discuss dimensional stability of dyed fabric to washing. DALO® Textile Marker DIRECTIONS FOR USE To start flow press rubber bulb to pressurize. The measured dimensional stability of a fabric determines whether a fabric has the potential to retain its original shape and remain stable, indicating it will not bubble or sag over time, when applied over a substrate, and its suitability for a specified use. It is required to confirm about the dimensional stability of a dyed fabric. Last Updated on Dimensional Stability to Washing of a Dyed Fabricĭimensional stability is the vital characteristics of a fabric. Advantageous for its ultra high capacity, the Dalo Textile marker provides a bright, sharp, rapid drying permanent mark on synthetic and synthetic/cotton.

Dalo textile markers